Launch Special: 20% OFF All Products!

Ends Nov 30, 7:19 PM PHT

Per DTI Fair Trade Permit No. 8442440, Series of 2026

Streaming & cameras

Your camera, in the room and on the stream

Connect a USB camera, an IP camera or a phone, cut between cameras with one key, put the camera behind any slide on your projector, and give your live stream a camera layout with the lyrics and your church logo on top.

Last checked 8 min read
On this page
  1. Connect a camera
  2. Go on air, and cut between cameras
  3. Way 1: the room, with the camera behind the slide
  4. Camera, layout and template text: the Text on layout switch
  5. Way 2: the live stream, with a camera layout
  6. Lyrics and your logo on the stream
  7. If something isn't working

One camera can serve two audiences. In the room, the camera sits behind the slide, so the congregation sees the stage with the words in front. On the live stream, the camera fills the frame, with the lyrics along the bottom and your church logo in the corner. This guide covers both, after connecting a camera.

Watch: Your camera, in the room and on the stream (about 4 minutes)

Connect a camera

Click Camera above the Master Output monitor. The button is always there, whatever is live, so you can set your cameras up before the service.

Cameras plugged into this computer are listed, ready to click. IP camera and Phone camera sit underneath.
Kind of cameraHow to add it
USB camera or capture cardPlugged into this computer, it is listed in the panel. Click it.
IP cameraClick IP camera, paste its RTSP address from the camera's app or manual, and give it a name. If it asks for a login, add the user and password: they are kept encrypted on this computer only.
PhoneClick Phone camera. A QR code appears. Join the phone to the same Wi-Fi, scan the code, open the link and tap Start camera. No app is needed, and the phone shows up in the panel by itself.
An IP camera: its RTSP address and a name such as Pulpit camera.
A phone as a camera: scan the code, tap Start camera.

Go on air, and cut between cameras

  1. Click your camera in the list, then click Put camera on air.
  2. To add another camera, click Add camera beside the first one and pick it, or pair a phone.
  3. Each camera has a number. Press its number, or click its card, to cut to it. The camera on air wears a red On air tag.
  4. Under Switch with, choose how the cut looks: Fade, Cut or Dip to black.
Two cameras side by side. Press 1 or 2 to cut.

Way 1: the room, with the camera behind the slide

  1. In the Camera panel, on the Look tab, Behind the slide is already chosen. The camera replaces the slide's background, and the words stay on top. This works for songs, Bible verses and presentations.
  2. Pick a look. Lyrics first dims and softens the picture, so every word stays easy to read. The sliders fine tune it: Dim, Soft focus, Black and white and Bottom fade.
  3. On the Screens tab, tick the screens that show the camera. Main Screen is your projector and is ticked to start with.
  4. Close the panel. The room sees the camera, with the words in front.
Behind the slide, then a look. In front covers the slide with the camera instead.

Camera, layout and template text: the Text on layout switch

When a screen layout is pinned under the monitor, the Text on layout switch beside the pinned cards decides what happens to the words. It works the same for lyrics and Bible verses.

  • On: the live song or verse is forced on top of the layout in its template text, whatever the layout holds. With the camera on air, it sits right behind the words.
  • Off: the layout shows its own content. On Message & Scripture, for example, the verse goes back into the layout's Scripture box.
On: template text on top, the camera behind.
Off: the layout as designed.

Way 2: the live stream, with a camera layout

For the stream, build a Broadcast layout whose canvas is the camera, then put the lyrics and your logo on top as overlays.

  1. Click Layouts in the menu bar, choose Broadcast, and click New layout.
  2. The layout editor opens on a starter design. Press Command A (or Control A on Windows), then Delete, for a clean canvas.
  3. Click Broadcast Content, then Camera.
  4. Right click the camera and choose Fill the canvas. Name the layout and close the editor: it saves as you go.
  5. In Layouts, right click your new layout and choose Pin to Broadcast.
  6. On the Master Output, open the Broadcast tab. Your pinned layout is a card under the picture. Click it, and the camera fills the stream.
One camera box, filling the canvas.
The Broadcast tab: click the pinned card to put it on air.

Lyrics and your logo on the stream

  1. Click Overlay in the header, then the Lyrics tab.
  2. Tick the Broadcast column. The lyrics ride on top of the camera as a lower third, and follow every slide you play.
  3. On the Props tab, click Pin props, pin your church logo, and go back.
  4. Click the logo's card to put it on air. A new prop starts on Main Screen: tick Broadcast, then untick Main Screen, so the logo shows on the stream only.
The Lyrics overlay, sent to Broadcast.
Your logo, on Broadcast only.

If something isn't working

My camera isn't in the list

Check that your computer lets ChristChant use the camera: on Windows, Settings, Privacy & security, Camera; on a Mac, System Settings, Privacy & Security, Camera. Then open the Camera panel again.

The phone link says it is not active

Each QR code is for one phone. Close the Phone camera panel and open it again for a fresh code. If two copies of ChristChant run on the same computer, close the other one: only one can receive phone cameras.

The room shows the words but no camera

Open the Camera panel's Screens tab and check that Main Screen is ticked, and that the camera is on air.

More about the camera settings: Put a live camera on your screens. Sending the stream out: Stream your service: NDI, SDI or go live directly.

Was this helpful?

Your answer helps us improve this guide.